Apatent application was made in 1981 for the earth shattering invention of "the original – LUX ELEMENTS® hard foam support ELEMENT".
The construction panel for walls and floors LUX ELEMENTS®-ELEMENT
The installation cladding LUX ELEMENTS®-TEC
Bath surrounds LUX ELEMENTS®-TOP
The washstands LUX ELEMENTS®-LAVADO
Point drainage LUX ELEMENTS TUB®
Linear drainage LUX ELEMENTS TUB-LINE®
Individual relaxation and distraction LUX ELEMENTS®-RELAX
The decorative elements LUX ELEMENTS®-DECO
Individual room constructions LUX ELEMENTS®-CONCEPT
The tried and tested accessories are fully harmonised for processing ELEMENT. Specially developed adhesives and mortars, sealing tapes, mounting angles and plugs ensure problem-free processing.
Fastening set and dowels LUX ELEMENTS®-FIX
Technical fixtures, Heating, Lighting and Sound LUX ELEMENTS®-ADD
Adhesives LUX ELEMENTS COL®
Sealing filler and sealing tapes LUX ELEMENTS®-DRY
Reinforce LUX ELEMENTS ARM®
Mounting aids LUX ELEMENTS MONT®
LUX ELEMENTS®-...-PLUS Individual, special manufacture for each product group
In addition to standard products, also individually tailored and specially manufactured products are available for the products groups listed under the designation ‘PLUS‘.
Sizes, shapes, thicknesses etc., that deviate from standard features can be inquired from LUX ELEMENTS. After successful verification of implementation possibility at LUX ELEMENTS an appropriate offer will be prepared. Once an order is placed, it will be manufactured and delivered accordingly.
Overview of All Issues
LUX ELEMENTS GmbH & CO KGAn der Schusterinsel 7D - 51379 Leverkusen-OpladenTelefon +49 (0) 21 71/ 72 12 - 0Telefax +49 (0) 21 71/ 72 12 40
Construction & design
Check subsurface for load-bearing capacity, remove the separating layers, check suction performance. If required, free from dust, premoisten and prime.
All ELEMENT construction panels must be stored lying down straight in a dry place. If an ELEMENT construction panel should be slightly warped due to improper storage or other reasons, they can usually be straightened by light bending and pressing.
Before applying the adhesive in dots, pre-pierce the holes for the dowels with a cross slot screwdriver.
Cuts and notches are made quickly and easily with the jig saw or a cutter knife.
Depending on the evenness of the subsurface, apply the fixing adhesive COL-AK pointwise on one side using clots of adhesive (6 – 8 pcs. per m2).
If ELEMENT-EL Baby 4 is used, always apply the fixing adhesive COL-AK over the full surface using a toothed trowel. This technique is also possible for thicker panels, depending on the substrate.
Apply the fixing adhesive COL-AK to the edges of the ELEMENT construction panels, thus bonding the individual elements together.
We recommend horizontal placing for ELEMENT. Draw alignment markings before application, if possible. Then press on the ELEMENT with the level and spirit level and check not only the individual but also the reciprocal vertical ...
... and horizontal alignment of the ELEMENT construction panels.
TIP: Pre-drill dowel holes. Then ...
... dowel with FIX-FID or FIX-KSD. Pay attention to water and power lines!
All element joints must be reinforced with glass fibre reinforcement strips ARM-100 SK.
Level out the reinforced element joints and the heads of the hammer fix plugs with COL-AK.
The surface is now ready for tiling. Further requirements (e.g. sealing for wet loads) must be taken into consideration in accordance with national directives.
© 2022 All rights reserved. We reserve the right to make technical changes.Status: Feb 11,2022
LUX ELEMENTS GmbH & CO KGAn der Schusterinsel 7D - 51379 Leverkusen-OpladenGermanyTelefon +49 (0) 21 71/ 72 12 - 0Telefax +49 (0) 21 71/ 72 12 40